Sale!

areyoulookingtopurchaseanduotight8mmxflowcontrolballlockdisconnectliquidblackyellowpokkeglandpurchasenowbeforetheygooutofstock0.jpg

duotight | 8mm x Flow Control Ball Lock Disconnect (Liquid Black + Yellow) (POK) Kegland

$ 8,97

SKU: mode_6755664953390 Category: Kegging Tags: ball lock disconnects, beer line, beer lines, brewery equipment, disconnect, disconnects, duotight, Equipment, flow control, Kegging, MFL Disconnects

Description
shopping

If you want an easy way to balance your beer lines this is the way to do it. Please be aware that even in the fully open position these FC disconnects do have some inherent flow resistance so you should use either shorter line or larger ID line that you would when compared with traditional ball lock disconnects. One of the benefits of FC disconnects is you don’t need to rely on the small ID or line length to apply flow resistance so it would not make sense to use long lines or small ID lines as well as this is the job of the FC device.

This is perfect for people who want to serve a large range of beverages with differing carbonation levels as it gives you the ability to adjust resistance easily. Now with the added benefit of duotight fittings built in.

This particular ball lock disconnect has been designed to suit 8mm Beer Line. Due to the integrated duotight fitting the line will simply push directly into this fitting.

For this ball lock disconnect we recommend using either:

EVABarrier 4mm ID x 8mm OD Line

EVABarrier 5mm ID x 8mm ID Line

Why not a flow control tap/devices?

Flow control devices are good but they inherently can create a small amount of turbulence and therefore can cause foaming. In the past flow control taps have been the only common option. Flow control taps are popular however they have the issue that due to the fact they are placed right at the end of the beer line they have no head pressure. As a result any turbulence created can cause foaming and carbonation to come out of solution.

Flow control ball lock disconnects like these on the other hand have the ability to restrict the flow before the beer enters the beer line so the head pressure created by the beer line keeps the carbonation in solution. Even in the instance that high turbulence is created the beer will be far more resistant to foaming issues. For this reason flow control ball lock disconnects like these have significantly better performance allowing you the flexibility to adjust line resistance easily but without the introduction of turbulence that creates foaming. It cannot fix over-carbonated beer, but it can reduce the amount of beer line you would need to pour without excessive foaming.

Product Features:

POK Injection-moulded Design.

Like all new duotights push in fittings all of them are manufactured with polyketone plastic (POK). This aids in chemical resistance, tensile strength, and toughness.

duotight push in

These duotight ball lock disconnects already have the duotight fitting built into the ball lock disconnect. No need for additional threaded fittings. Simply push the beer/gas line in and you are done!

Compact

The worlds most compact ball lock disconnect every manufactured. This new compact form factor is great for tight spaces or fridges where you want to pack as many kegs in as possible. This is the only ball lock disconnect that allows standard ball lock kegs to be double stacked while still connected to beer and gas lines.

Overmoulded Poppet

The overmoulded poppet design means you can couple and disconnect this ball lock disconnect under extreme pressures of 150psi and will never have issues with the o-ring blowing out.

Tool-less Disassembly

Other ball lock disconnects require a tool such as a flat head screw driver or spanner to take them apart for cleaning. The new caps on these allow for easy disassembly by hand, making these easier to break down for cleaning. It’s literally never been easier to remove hop particles from your ball lock disconnects.

Extreme Chemical Resistance

No cheap ABS plastic or nitrile seals. This ball lock disconnect is made from stainless spring and ball bearings, with an engineering polykeytone resin body, EPDM and PP/EPDM overmoulded poppet. This makes this ball lock disconnect resistant to extreme chemicals such as phosphoric and acetic acid, caustic soda, peroxide and many other acid or base chemicals which are commonly used in homebrewing.

Toughness

This ball lock disconnect is more robust than any other plastic ball lock disconnect ever manufactured due to the use of new engineering plastics. Don’t be fooled by the small form factor – these bad boys are tough.

Fast shipping and professional packing

We offer a wide range of shipping options due to our long-running partnerships with UPS, FedEx and DHL. Our warehouse staff are highly trained and will package your items according to our precise and precise specifications. Before shipping, all goods are thoroughly inspected and securely secured. Every day we ship hundreds of packages to our customers from all over the world. This is a sign of our commitment to be the largest online retailer worldwide. The warehouses are located situated in Europe as much as they are in USA.

Note: Orders containing multiple items will have a different processing period for each item.

Before shipping the items, our staff will carry out an extensive inspection of the products you have ordered. The majority of orders are delivered within 48 hrs. The delivery time should be between 3-7 working days.

Returns

We don't manage the stock in our factory and warehouse. Actual stock levels may fluctuate at any moment. Be aware that it's possible that your order will be out of stock after you have placed the order.

Our policy is for 30 days. Unfortunately, if 30 days have passed from the date you purchased the product, we are unable to offer you a return or exchange.

The item must not be used, and it must be in the original packaging. It must also be in the original packaging.